Clear PVC Spiral Reinforced Hose – Steel Wire Suction Hose
Clear PVC spiral reinforced hose with high-carbon steel wire helix — kink-resistant, chemical-resistant, rated -10°C to +65°C. Request a free quote today!
- Overview
- MOQ & Lead Time
- Free Sample & Technical Support
- Recommended Products
- Measure the run and cut the hose square with a hose cutter — a clean, burr-free cut is what keeps the joint leak-free.
- Wrap the cut end with tape before cutting if the wire ends may protrude, then remove the tape.
- Soften the end in hot water for 30–60 seconds to make the PVC pliable.
- Push the barbed fitting fully home, past the last barb, in one steady motion.
- Fit two clamps behind the barb and tighten evenly, 180° apart.
- Pressure-test at 1.5× working pressure for 5 minutes before putting the line into service.
- Keep the bend radius at 6× outside diameter or more; a tighter bend stresses the wire and shortens service life.
- Cut the PVC spiral reinforced hose with a hose cutter, never a saw — a frayed wire end will pierce the wall. Do not drag it over sharp edges or hot surfaces, and do not use it for aromatic solvents, concentrated acids or ketones.
- Store coiled, flat, out of direct sunlight, away from heat sources and ozone-generating equipment.
- For vacuum duty, keep the coil ends straight for at least 3× the diameter to avoid stressing the helix.
- RoHS / REACH — test reports available for the standard phthalate-free compound.
- Food-contact grade — FDA 21 CFR 177.2600 and EU 10/2011 compliant compound on request, migration report supplied with the shipment.
- Antistatic grade — surface resistivity ≤ 10⁶ Ω for powder and solvent-free transfer where static build-up is a risk.
Product Overview
FOSITE clear PVC spiral reinforced hose is a flexible, transparent suction and discharge hose built around a high-carbon steel wire helix, made for distributors, industrial buyers, farms and OEM brands that need dependable fluid transfer in demanding conditions. The crystal-clear PVC wall lets operators see the flow at a glance, while the embedded spiral wire stops the hose from collapsing under vacuum and keeps it from kinking when it is dragged across a jobsite. Available from 1/4 inch to 8 inch inner diameter in phthalate-free, food-grade and antistatic compounds, it handles water, mild chemicals, slurry, light solids and food-grade transfer — supplied in coils, cut lengths or fully assembled with couplings. Every PVC spiral reinforced hose order is produced to your bore, wall thickness and pressure class.
Key Features
1. Steel wire helix reinforcement
High-carbon galvanized wire is wound continuously into the wall, so the hose resists vacuum collapse and keeps its full bore on tight bends instead of flattening like an unreinforced tube.
2. Crystal-clear transparent wall
The see-through PVC shows blockages, air bubbles and product colour instantly — operators spot a starved pump or a slug of air before it becomes downtime.
3. Wide size and pressure range
PVC spiral reinforced hose sizes run from 6 mm to 200 mm (1/4" to 8") inner diameter, wall 2.0–8.0 mm, working pressure 0.3–0.8 MPa by size, burst pressure at least 3× the working rating.
4. Chemical and abrasion resistance
The smooth bore resists mild acids, alkalis, salt water, detergents and suspended solids, which makes this PVC spiral reinforced hose suitable for slurry and light-solids transfer as well as clean water.
5. Temperature and weather tolerance
Stable from -10°C to +65°C in continuous service; a UV-stabilised compound is available for outdoor irrigation and long-term sun exposure.
Specifications
| Product name | Clear PVC spiral reinforced hose (steel wire helix suction & discharge hose) |
| Material | Virgin PVC compound, phthalate-free (DEHP-free); food-grade compound optional |
| Reinforcement | High-carbon galvanized steel wire helix, 0.8–2.0 mm wire by bore |
| Inner diameter | 6–200 mm (1/4"–8") — full range in 0.5 mm / standard inch steps |
| Wall thickness | 2.0–8.0 mm, tolerance ±0.3 mm |
| Colour | Crystal clear with blue + red stripe (standard); custom colour and stripe on request |
| Working temperature | -10°C to +65°C |
| Working pressure | 0.3–0.8 MPa (varies by bore and wall) |
| Burst pressure | ≥ 3× working pressure |
| Vacuum rating | Up to -0.09 MPa (full vacuum for sizes ≤ 50 mm) |
| Hardness | 65–80 Shore A |
| Bend radius | ≥ 6× outside diameter |
| Standard length | 30 m / 50 m / 100 m coils; cut lengths to order |
| Compliance | RoHS / REACH test reports; food-contact grade to FDA 21 CFR 177.2600 and EU 10/2011 on request |
| MOQ | 500 m per size |
| Lead time | 15–25 working days after deposit |
Materials & Finish
| PVC compound | Virgin suspension PVC with a phthalate-free plasticiser, formulated in-house and granulated before extrusion. No recycled regrind goes into the wall, so clarity and pressure rating stay consistent from coil to coil. |
| Wire reinforcement | High-carbon steel wire, galvanized for corrosion protection, spiralled at a pitch matched to the bore — tighter on small sizes for pressure, wider on large sizes so the hose still coils easily. This is what keeps the PVC spiral reinforced hose open on a tight coil. |
| Extrusion | The wall is co-extruded in a single pass around the wire helix, which bonds the wire to the PVC without glue lines or voids and gives a wall thickness tolerance of ±0.3 mm. |
| Surface and finish | Glossy, low-friction bore for high flow and easy cleaning; smooth exterior that resists dirt build-up. A matte exterior is available for handling-heavy applications. |
| Colour coding | The blue and red stripe is co-extruded, not painted, so it will not peel; stripe colour can be matched to your brand or used to code size and pressure class. |
| Optional compounds | Food-grade (FDA / EU 10/2011), antistatic (surface resistivity ≤ 10⁶ Ω), UV-stabilised for outdoor duty, and a cold-flex compound rated to -20°C. |
Assembly & Installation
Tools needed: hose cutter or sharp knife, barbed insert fittings, hose clamps (2 per joint), hot water (60–70°C) for softening, pressure gauge.
Assembly steps
Usage notes
Applications
The PVC spiral reinforced hose is specified wherever a clear line has to bend around equipment, survive vacuum and still let the operator see what is moving through it.
Agricultural irrigation & spraying
Drip and sprinkler feed lines, pesticide and fertiliser transfer, greenhouse watering; the clear wall lets growers confirm flow at each outlet.
Pump suction & site dewatering
Construction dewatering, sump and trash pump suction, flood recovery; this is the classic PVC spiral reinforced hose duty, where the wire helix holds shape under negative pressure.
Industrial fluid transfer
Machine coolant, hydraulic fluid return lines, chemical dosing and tank filling in workshops and small plants.
Food & beverage handling
Milk, juice, syrup, edible oil and CIP cleaning lines with the food-grade compound; smooth bore supports flushing between batches.
Aquaculture & fish ponds
Pond drainage, aeration supply, water exchange and fish-transfer lines in fresh and salt water.
Mining, slurry & light solids
Tailings lines, sand and gravel wash-down, powder and granule conveying where abrasion resistance matters.
Pool, spa & cleaning
Pool vacuum heads, spa drain-down and general washdown duty; light enough to handle by one operator.
Customization
| Size | PVC spiral reinforced hose ID 6–200 mm; wall 2.0–8.0 mm; non-standard bores to drawing |
| Colour & stripe | Clear, or tinted blue / green / red; stripe colour and width to brand spec |
| Compound | Food-grade, antistatic, UV-stabilised, cold-flex (-20°C), oil-resistant |
| Printing | Brand, size, working pressure and certification mark printed on the wall |
| End fittings | Plain cut, barbed insert, camlock, flange, or assembled with strainer / nozzle |
| Packaging | Coil with PE film + woven bag, carton, pallet, or custom retail label |
| OEM / ODM | Private label from 500 m per size; artwork and colour card support |
Certifications & Compliance
Packing & Logistics
| Packing | PVC spiral reinforced hose coils of 30 / 50 / 100 m, wrapped in PE film then woven bag; carton or pallet for retail and LCL shipments |
| Labelling | Size, length, working pressure and batch number printed on each coil label; buyer's shipping mark accepted |
| Loading reference | 1×20GP approx. 12–15 t; 1×40HQ approx. 24–26 t (coiled hose, by size) |
| Port of loading | Tianjin / Qingdao / Ningbo |
| Incoterms | FOB / CIF / CFR / DDP |
| Sample | 1 m cut sample free of charge, freight collect |
Service
| Free sample | 1 m PVC spiral reinforced hose cut length per size, freight collect, dispatched within 3 working days |
| Response time | Within 24 hours on working days, with technical answers on sizing and fittings |
| Warranty | 12 months against manufacturing defects; normal wear, UV ageing and misapplication excluded |
| Technical support | Bore / pressure / bend-radius selection and fitting matching for your line |
| Spare supply | Repeat orders from stock for the ten fastest-moving sizes |
FAQ
Q: What is a PVC spiral reinforced hose?
A: It is a flexible PVC hose with a high-carbon steel wire wound in a spiral inside the wall. The wire carries the load, so the hose can be pulled, bent and used under vacuum without collapsing — something a plain PVC tube cannot do.
Q: What sizes and pressures can you supply?
A: Our PVC spiral reinforced hose runs from 6 mm to 200 mm (1/4" to 8"), wall 2.0–8.0 mm, working pressure 0.3–0.8 MPa depending on bore, with a burst rating of at least three times the working pressure. Tell us the medium and flow rate and we will confirm the size.
Q: Can this hose be used for suction duty?
A: Yes. The steel helix is bonded into the wall, so a PVC spiral reinforced hose keeps its bore open under negative pressure, up to full vacuum on sizes 50 mm and below. For larger sizes we recommend a heavier wall, and the coil ends should be kept straight for at least three diameters.
Q: Is the hose food-grade?
A: The standard compound is phthalate-free but not food-contact certified. We supply a food-grade version tested to FDA 21 CFR 177.2600 and EU 10/2011 on request, with the migration report attached to the shipment.
Q: What is the MOQ and lead time?
A: Standard MOQ is 500 m per size of this PVC spiral reinforced hose, and production takes 15–25 working days after deposit. Trial orders below MOQ can be discussed for stock colours.
Q: How is the hose packed and loaded?
A: Coils of 30, 50 or 100 m are wrapped in PE film and woven bag, then cartoned or palletised. A 20GP takes roughly 12–15 t and a 40HQ 24–26 t, depending on bore.
Q: Can you print our logo on the hose?
A: Yes. Brand, size, working pressure and certification marks can be printed on the wall, and the stripe colour can match your brand. Private label starts from 500 m per size.
Standard MOQ: 500 m per size. Lead time: 15–25 working days after deposit. Trial orders below MOQ can be discussed for stock colours.
1 m cut sample free of charge (freight collect), dispatched within 3 working days. Bore / pressure / bend-radius selection support answered within 24 hours.
